Encore SP201-SA Manual do Utilizador descarregar pdf

encor

•

etworks

SignalPath

™

201-SA

(SP201-SA

™

)

Installation Guide

Version C, July 2004

Part Number 15469.0100

SignalPath Software Version 1100

This Installation Guide presents a quick, standard installation of the SP201-SA.

Note: The needs of your network may require an installation that varies from the standard installation.

For a customized installation, see the SP201-SA Customization and Maintenance Guide. For hardware

information, see the SP201-SA Hardware Reference Guide.

The SP201-SA is available in two versions:

• The two-port SP201-SA, supporting one trunk circuit of up to 30 channel circuits

• The four-port SP201-SA, supporting up to two trunk circuits of up to 30 channel circuits each (for a total

of up to 60 channel circuits)

Note: A standard trunk circuit (from one external device, through the SP201-SA, to another external

device) comprises trunk connections to two ports. The SignalPath™ configuration software defines each

side of the trunk circuit (that is, each connection to a port) as a trunk.

This document uses the term trunk to indicate a connection to one port; it uses the term trunk circuit to

indicate the complete end-to-end connection (over two ports). Using these definitions, a trunk circuit

comprises two trunks.

Before you start this installation, be sure you have filled out the worksheet for adding this device to your

network. See the SP201-SA Site Planning Worksheet.

See the following sections for a standard installation of the SP201-SA:

• Section A, Physical Installation

• Section B, Port Configuration

• Section C, Clocking Configuration

• Section D, Trunk Configuration

• Section E, Channel Configuration

• Section F, SP201-SA Warmstart

1 2 3 4 5 6 ... 13 14

Resumo do Conteúdo

encoren!•etworksTMSignalPath™ 201-SA(SP201-SA™)Installation GuideVersion C, July 2004Part Number 15469.0100SignalPath Software Version 1100This Instal

Página 2 - A Physical Installation

10 SP201-SA™ Installation GuideE.4 Channel Configuration for N5 Signaling What the terminal displays What you type What you are configuringuser>

Página 3

SP201-SA™ Installation Guide 11Template # for default IAM ? : (range 1 - 5) : <current=1> 1Default values for IAM parameters required on the SS7

Página 4 - B Port Configuration

12 SP201-SA™ Installation GuideE.5 Channel Configuration for ETSI ISDN In the two-port SP201-SA, perform the following procedure once for trunk 2. In

Página 5 - C Clocking Configuration

SP201-SA™ Installation Guide 13E.6 Channel Configuration for NI2 ISDN In the two-port SP201-SA, perform the following procedure once for trunk 2. In t

Página 6 - D Trunk Configuration

14 SP201-SA™ Installation GuideF SP201-SA WarmstartThis completes the standard installation. To configure other parameters, see the SP201-SA Customiza

Página 7 - E Channel Configuration

2 SP201-SA™ Installation Guide Figure 1. SP201-SA ChassisNote: The cables you connect to the SP201-SA depend on the protocols. The following table li

Página 8

SP201-SA™ Installation Guide 3Note: Channels on trunk 1 of the two-port SP201-SA map to channels on trunk 2, and vice versa. In a standard installati

Página 9

4 SP201-SA™ Installation GuideB Port Configuration What the terminal displays What you type What you are configuringuser> config lim Interfaces

Página 10

SP201-SA™ Installation Guide 5C Clocking Configuration(Information on tests and restarts)(Boot banner and boot> prompt) (Do not type anything. The

Página 11

6 SP201-SA™ Installation GuideD Trunk Configuration Perform the following procedure once for each trunk on the SP201-SA. What the terminal displays W

Página 12

SP201-SA™ Installation Guide 7E Channel Configuration See the following sections to configure the protocols in your SP201-SA: E.1 Channel Configuratio

Página 13

8 SP201-SA™ Installation GuideE.2 Channel Configuration for R1 SignalingWhat the terminal displays What you type What you are configuringuser> c

Página 14 - F SP201-SA Warmstart

SP201-SA™ Installation Guide 9E.3 Channel Configuration for R2 Signaling What the terminal displays What you type What you are configuringuser>