Encore ENNUS1 Manual do Utilizador

ENNUS1 USB-OVER-NETWORK SERVER User Manual 0

You must change the IP address (or using DHCP) of the ENNUS1 server so that the ENNUS1 server and your PC are in the same subnet. To do this, pleas

C. When the installation program asks you to plug-in the USB device, run the “Control Center”. D. In the Control Center, click the ENNUS1 server t

4.5 Using the ENNUS1 Server A. In the Control Center, click the ENNUS1 server that has the desired USB device attached. B. Click the desired USB

4.6 Auto-Connect Printer The method described in section 4.5 is called “manual connect”, which means users must manually connect and disconnect

The following window will appear. D. Choose the desired printer. The desired printer must be the Windows printer (this is a logical printer) tha

F. Try to issue a print job to the desired printer. The Control Center will automatically do a connect operation. The print job will be issued to

C. Click the “Network Scanner” button. Then you can see that the Control Center will automatically do a “connect” operation. The following wind

E. Follow the usual steps to do scanning. F. After the scanning, close the “Auto-Connect Scanner” window. At this moment, Control Center will au

You can see the storage icon in the system tray. Use the new disk as a regular disk. When you are ready to disconnect the disk, click the stora

At this moment, the user on the TEST1 computer will see the following window, indicating that another computer – TEST2 is requesting to use the H

Table of Contents CHAPTER1 INTRODUCTION ...

Chapter5 The Control Center This chapter describes how to use the Control Center. 5.1 Installing Control Center 1. Insert the included CD i

5.2 Using the Control Center You can use the following tools to help you use the ENNUS1 server:  Configure Server: go to the server’s web pag

Chapter6 The ENNUS1 Server’s Web Pages 6.1 Introduction The ENNUS1 server runs the http server on TCP port: 80. Users may use the web pages to

6.2.2 Setting up ENNUS1 Server Configuration To set up the ENNUS1 Server configuration, click on the “CONFIG” icon and then the system will reques

 Maintenance If you want to restore factory default values of the ENNUS1 Server or upgrade new firmware, you can use the Maintenance tool. 5 R

24

Chapter7 Troubleshooting This chapter provides useful information to help you resolve difficulties that you may experience with your ENNUS1 Serv

Chapter8 Restore Factory Defaults You may restore the ENNUS1 Server’s default parameters by one of the following methods. 8.1 Using the ENNUS1

8.3 Default Parameters List Server Information z Server Name: ENNUS1 TCP/IP z Automatically get IP by DHCP: Enabled - Manual DNS: None (Disable

Chapter9 Upgrade Firmware This chapter describes how to upgrade firmware. Please follow one of the following methods: Method A: Using the ENN

Chapter1 Introduction Thank you for purchasing Encore ENNUS1 USB-OVER-NETWORK SERVER (in the following referred to as “ENNUS1 Server”). ENNUS1 Se

Chapter10 The Init Button The Init button is used for maintenance: Simultaneously press Init button and turn on (by plugging in the power adap

Chapter2 Product Overview 2.1 Package Contents Verify that nothing is missing from the package by using the checking list below. Please contact

Chapter3 Basic Installation 3.1 Connecting the Hardware 1. Make sure that your USB devices are switched off and that the ENNUS1 Server’s pow

3.2.4 Server Names and Server Name Rules The default server name of the Server is “ENNUS1”. If you have multiple Servers in your local area networ

5. Click the “CONFIG” button and enter the ENNUS1 Server’s administrator (default: admin) and password (default: admin). 6. After you login

7. Click the button corresponding to your choice of IP setting method (static or dynamic using DHCP). When assigning a static IP address you also

Chapter4 Using the ENNUS1 Server 4.1 Introduction The goal of this product is to provide connectivity to USB devices from a single server. A n